Ect122 w2 ilab 3

A Galvanometer is used to measure the current of the circuit and the Wheatstone Bridge is used to measure the resistances and determine the unknown resistance. It has changed the way we do everything. Connect the hand-held DMM voltmeter across the 1k resistor as shown below.

Determine the total current in the following nodes. Without electricity the lights go off, water is not heated, the television goes off, and outside the traffic lights do not work and as a result the city is immediately congested with traffic jams and choke ups in the street.

The nature of the magnetic field lines around a straight current carrying conductor is concentric circles with centre at the axis of the conductor. To get familiarize with the meaning of linearity by plotting the V-I volt-ampere curves characteristics of a linear device.

Determine the potentiometer setting needed to set the current in Figure 4.

This Tutorial contains following Attachments

This process includes a test coil through which vary or alternating current AC is passed. All of these need electricity to work. Draw a simple circuit containing an open circuit. Install this wire so that it is in the same row as the second lead of the resistor. Question 3 Name the instrument used to measure electric current in a circuit.

This Tutorial contains following Attachments

Direct-Current Voltmeter The direct-current voltmeter has a horseshoe shaped magnet, with a semicircular piece of soft iron attached to each end of the magnet.

Conductor - is a material which contains movable electric charges. I know that as resistance changes, current changes, as Ohm's law: The electromagnetic field produced around the coils is directly Record the results in Table 1.

From there we assigned ourselves different components to understand what they were and how they worked inside the amp.

Electric current Essays and Research Papers | examples.essaytoday.biz

Run the simulation and record the voltmeter readings. There our four different things that affect the resistance of a wire: Mere the current and record it in Table 1. Electricity, Magnetism, and My Electric Motor.

Once you have calculated the power value, click on the wattmeter symbol and record the value.

Ohm's Law is made from 3 mathematical Resistance is measured in Ohms. Ammeter An ammeter is used to measure current. To design an experiment that will facilitate an I - V Graph to be ascertained of a metal wire and thus find the resistance of the wire by deriving the inverse of the gradient of the graph.

If both resistance and voltage double the current remains the same. Resistance is a force, which opposes the flow of an electric current around a circuit.

It continues to rank as the fourth highest cause of industrial Ia is the current in Figure These unique freshwater predators got their name from the immense electrical charge that they can easily generate to stun or even kill their preys and dissuade predators.

There are two types of circuit's Parallel circuit, and Series circuit. From the tape player to the electric pumps that send hot water to each of our homes everyday.

ECT Week 5 iLab #3 1. Determine the load voltage by deriving an equivalent circuit for the circuit below. Reduce the R1, R2, and R3 combination to a single equivalent resistance.

ECT Week 2 iLab #3 Part 1 Parts: Breadboard DC Power Supply Hand Held DMM Test leads Wire 56kΩ resistor. ECT Week 4 iLab 3 This Tutorial was purchased 1 times & rated No rating by student like you.

mobile-concrete-batching-plant.comate the current in each branch of the parallel circuit below. View Lab Report - w2_iLab_2 from ECT ECT at DeVry University, Chicago. ECT Week 2 iLab #2 Part 1 Never connect the Positive (+) lead of a power supply to the ground.

Connect the negative. May 02,  · Words | 3 Pages Electric Current and Current Flow GRADE: 8th TEACHER: Mrs. Russo I. Statement of Purpose and Hypothesis: Our purpose for this project was to find out what fruits and vegetables could generate an electric charge.

ECT Week 2 iLab #3. Part 1. Parts: Breadboard. DC Power Supply. Hand Held DMM. Test leads. Wire. 56kΩ resistor. Given the circuit below, use Ohm’s law to determine the total current in the circuit and the voltage across the resistor.

Ect122 w2 ilab 3
Rated 4/5 based on 91 review
ECT Week 3 iLab 3 by Roberto Leary on Prezi